- The goal of Spout
- Parts list
- Tool list for Spout
- Tools and parts to build a Spout
- Connect the SPDT switches
- Attach the LED eyes
- Wire the SPDT switches
- Create the motor mounts
- Secure and wire the motors
- Install on/off switches
- Connect the LEDs to an on/off switch
- Attach Spout's antennae
- Add Spout's tail
- Give Spout some grippy feet
- Spout in a maze
Created by Karl Wendt.
Want to join the conversation?
- At2:24, can the wire be attached to the switches before the switches are glued to the battery holder?(10 votes)
- how old do you need to be to do this alone?And if you are yong and can't work alone how old would the help need to be.(6 votes)
- Could you use hot glue instead of the electrical tape on the red wires / LEDs connection?(5 votes)
- I don't think so. Hot glue doesn't act as a great insulator but is a great connector. Electrical Tape works as both. The hot glue could drop off and they wires could touch another connection to make a short.(4 votes)
- Can you connect a remote to your spout bot?And control it?They should make a section where they connect or build the remote don't you agree?(3 votes)
- I do agree, it would be more beneficial for the purposes of learning, but what if someone is trying to teach this to third graders? It would be hard enough as it is!(1 vote)
- At8:14, why are red LEDs used for eyes? Can you use other things or other LED colors?(2 votes)
- Do the resistors need to point in a certain direction? He does not specify if the current needs to flow through the resistors in a particular direction.(2 votes)
- I think I saw elsewhere that it doesn't matter which way the resistors are put in. Don't quote me though! :D(3 votes)
- Are you moving faster along building this bot, or are you just doing it in a different order?(2 votes)
- From where would I get this products in BANGLADESH anyone know?(2 votes)
- Alibaba? Amazon? An online hardware store would work, I guess. Since you would already know what you wanted, you could buy duplicates to make more that one!(1 vote)
- What are the pros and cons of stranded vs solid core wire?(1 vote)
- Hello Shawn,
Cost and performance.
For a given size the solid core wire is generally be less expensive as the larger conductors are easier to work - simple machines at factory. The solid wires are easier to terminate. Take your house wiring as an example. An electrician can strip the insulation and install a device such as a power outlet in less than a minute.
As a rule the stranded wire is more flexible and less prone to breakage. This is important for applications where the wire is continually stressed such as a power cord of electric guitar cable.
You may want to research "skin effect" and "litz wire."
OK, so in this video, we're going to connect our LED lights. The LED lights are going to be used to test various parts of the circuit, and they're also used as eyes. Now, LEDs are polarized, which means it does matter which direction the power flows through the LEDs. LEDs usually have one short leg and one long leg. The long leg is usually positive, and so we want to make sure that we match up our two long legs together. If we connect a short leg and a long leg together, it will have problems. They won't work the way they're supposed to do. So we're going to look for our two long legs. Once we've got those two long legs figured out, we're going to bend them out so that we can connect them together. And so we're going to display those two legs there on the LEDs, and now that we know that there are two positives together, we're going to twist them together-- just twist them around one another. And we want to make sure that the twists are very tight, so we have a really good, solid connection. So just keep twisting those legs until they've been twisted around each other probably between 5 and 10 times. So then we have the negative legs of the LEDs on the outside, and the positive legs are twisted together on the inside. So now what we need to do is we need to connect the LEDs to the switches. And the way we're going to connect the LEDs to the switches is first we're going to take some of the red wire that we had in our kit, and we're going to strip off about half of an inch of that red wire. And we're going to feed that red wire through the top connections. There's little tiny holes on each of those connectors on the back of our switches, so we're going to trying to run this wire through those holes. And this is probably the trickiest wiring part in the entire bot, because you have to bend the wire in a sort of a large loop or a hook shape to get it to go through both of the holes in each connection. So that's why we've got our trusty needle-nose pliers there. And it does take a little bit of doing, but you can get it to go through both of those holes. And it does help to make sure that the connection will be a good one. So there we go. We got the wire to feed through both holes there. So then I just bent the wire up at a 90 degree angle to the connector that it's going inside of, and I'll zoom in here just a bit just to make sure you can see what's going on. And in order for this particular [INAUDIBLE] bot build to work, we have to make sure that those wires are crimped, or bent, very tightly against the contacts. If there's a lot of space in between the wire and the contact, the bot may not function the way we want it to. So we're taking our needle-nose pliers and getting it into those tight spaces between the wire and the contacts and bending those wires tightly against the connections. And we're going to our LEDs to make sure that that connection is actually a good one and that power is flowing. So the next thing that we need to do is we need to trim our wire down just a bit. So we're going to cut out about two inches off of our wire. The wire that's remaining should be about an inch and a half long, and we're going to take off about a half an inch of insulation from that wire. So again, that's a 22 gauge wire, so it's really narrow, so we'll use the smallest hole on our wire stripper. And these are really low wire strippers, so you have to twist them a little bit to get the insulation to come off. OK, so now we have our red wire there. We also have the red wire coming from our battery. So what we need to do now is we need to connect our red wire from our battery to the red wire we just connected to our single-pole double throw switches. We're going to take a little bit more insulation off of this wire, so we also made it a little longer. So it's about two inches long, and we're going to take about 3/4 of an inch of insulation off of this wire with our wire strippers. And you've got to be careful, because this is a stranded wire. It's not solid, so it's easy to break the strands when you're stripping it. So you want to take your time to pull the insulation off carefully so that you have all those electrically conductive strands still connected. So then we're going to take those strands and we're going to take that wire and we're going to wrap it around the solid core wire, which is the one we just connected to the switches. And the best connections are really tightly wound, so we want to make sure that all of those strands are very tightly wound around that solid core copper wire there. And so that's going to make it easier for us to connect the positive side of our battery to our LEDs and to other components, as well. So we're going to take our LEDs, and we're going to connect the resistors to the LEDs. The resistors prevent the LEDS from taking too much current and burning out. So again, we're going to put the resistor leg at about 90 degrees opposed to the LED leg, and then we're going to just wind it around the LED leg. And we want to wind it around at least four or five times, if not more, to just make sure we've got a really solid contact connection with the LED leg. And again, that's the negative leg. And the resistors can go on either the negative or positive leg, but in this video, we chose the negative legs, which are the outside ones. So again, just twist it all the way around, until it's nice and firmly connected. It's important that those loops that we make with that resistor leg are very tight and firmly attached to the LED leg. OK, so now that we have our LEDs set up, we can begin to connect them to the red wires which we just wound around. Before we do that, we're going to just test to make sure everything works. Let's move it here so you can see it. OK, there we go, yeah. So we're getting power through the wires, and we'll try the other side. This just makes sure that we've wired our LEDs correctly. OK, so we have. And this is a low enough voltage circuit and low enough current circuit that we can just use our hands to connect these things. OK, so now let's connect our LEDs. Now that we know that power can flow through there, we're going to try and wrap our red wires around our LED positive legs, which are the center legs there. So we're going to try to twist everything together, and this may be a little difficult. So if it is, you can always take your needle-nose pliers and just crimp it on there and make sure that the wires are connected tightly. Now, the better this connection is, the more likely it's going to be reliable, so it's really important to make sure that connection is solid. OK, once we've got those wires twisted together and our LEDs are there, we can take a piece of aluminum foil and wrap it around just to help ensure that the wires are going to stay solidly connected and they conduct power. Now, you don't necessarily have to use the aluminum foil. It's just an added precaution, but basically it allows to make sure if there's any loose wire connections there, that we still get electrical conductivity. But again, you don't necessarily have to have that. OK, so now we're going to take some insulating material, which will be electrical tape. We're going to wrap it around our aluminum foil and the twisted together wires, and that should help to hold everything in place so that we have a reliable connection. And it's just a little bit out of the screen. There we go, moving it back into the screen. And you want to wrap that electrical tape as tightly as possible around that connection to help hold everything snugly in place. So now what we're going to do is we're going to connect our resistor leg and our black negative wire from our batteries to the two open terminals on our switches. And depending on which terminal you connect it to, the switch will turn it on or turn it off. And so one thing you want to be careful of is, you don't want to leave it on there too long, because when it's turned off, you can actually short the circuit, and that will cause the wires to heat up. But it does allow us to test the LEDs and to make sure that all of our connections are good, and they are. So we're going to hot-glue the red wires, which are the positive terminal wires, and that'll keep them from moving around and hold them against our single-pole double throw switches there at the top.